Why fabric and wood materials were used on F4Us

[ppopsie]

I have been wondering why these non-metal materials were mixed up on the structure of the Vought F4U Corsair, like;

1) partially fabric covered wing outer panel structure. The aircraft was supposed to be a high speed fighter. Fabrics should require more maintenance and were not significantly easy to patch up.

2)ailerons and some flap panels were made of wood. From my experience building them in plywoods was not greatly easier than in metals.

I understand the control surfaces in general had been fabric covered for the reason of weights on many aircraft types. I would like to know about them. TIA.

[FLYBOYJ]

Actually you have made good points. I believe some of these materials were used to save weight. In the day the Corsair was designed they were the norm. In actuality, holes are very easy to patch up if they were under a certain size and didn't require stitching. Fabric used in that day was either Irish linen or grade A cotton. Also the trim tabs were made out of wood. In later models all but the wood trim tabs were replaced.

[Soundbreaker Welch?]

Wood doesn't rust. Maybe that could be a reason.

[FLYBOYJ]

Originally Posted by Soundbreaker Welch?

Wood doesn't rust. Maybe that could be a reason.

No but it is affected by salt and humidity - in some cases you'd want rust instead of the kinds of defects you could get in wood!

[comiso90]

Perhaps the success of the Mosquito influenced engineers.

.

[ppopsie]

In my opinion the wood and fabrics were easy to dispose of. If the carrier needed more speed, just put them into extra boilers.....
------------------------
For serious discussion, as far as I know, the entire aileron and one or two panels of flaps are in wood, all covered with a layer of fabric to protect them from the moisture. It shall be far better to compare with flying fairly large Mosquitos from carriers like that the British Royal Navy did once, though.

Even the fabric covered part of the outer wing of the Corsairs have densely arranged ribs underneath which quite possibly increase the weight. As far as I can see it is almost twice in number than on the other all metal airplanes of the same era, in avarage.

[syscom3]

Originally Posted by comiso90

Perhaps the success of the Mosquito influenced engineers.

It influenced no one as the mossie was the last wooden plane to fly in a war.

Canvas and wood flight controls were being used since the beginning of flight.

One possible reason for the use of fabric control surface was the good strength to weight rations coupled with the need to reduce inertial forces under high deflections.

[comiso90]

Originally Posted by syscom3

It influenced no one as the mossie was the last wooden plane to fly in a war.

Canvas and wood flight controls were being used since the beginning of flight.

.

Yes but the tremendous success of the mosquito may may have caused designers a give second look at canvas and wood on a high performance fighter. I'm sure using fabric and wood on a first rate "modern" fighter wasn't popular with some engineers.

[syscom3]

Originally Posted by comiso90

Yes but the tremendous success of the mosquito may may have caused designers a give second look at canvas and wood on a high performance fighter. I'm sure using fabric and wood on a first rate "modern" fighter wasn't popular with some engineers.

The mosquito wasnt a fighter.

And anything that flew after 1945 that counted, was jet engined with metal control surfaces.

[comiso90]

Originally Posted by syscom3

The mosquito wasnt a fighter.

.

I never said it was

[Kurfürst]

I also wonder about this.... fabric covered control surfaces was pretty much what the majority of WW2 fighters used, with a few notable exceptions.

Why was it so popular with engineers for these applications, even though all-metal construction was used everywhere else?

[pbfoot]

Originally Posted by syscom3

It influenced no one as the mossie was the last wooden plane to fly in a war.

Canvas and wood flight controls were being used since the beginning of flight.

One possible reason for the use of fabric control surface was the good strength to weight rations coupled with the need to reduce inertial forces under high deflections.

I think the Vampire would have had some combat post WW2 and it;s got wood

[Snautzer]

I can think of this

Balloning of the fabric stuff occurs when the plane is in very high speed, so there was no direct reason (nothing to gain) to change.

Cost would also being a factor i guess as wood etc was the known

[ppopsie]

I asked the same question to multiple aviation people and got almost the same answer that to reduce the weight aft of hing lines was the primary reason. I understand this.

The situation changed when high speed planes with more than 400mph of top speed, like the Corsair, started to appear. The control force became increasingly heavier and heavier on these types. Most of the later WW2 American fighters suffered this problem.

.....So what were the airelons on the early prototype F4U(s)? Were these remain unchanged through its developing stage? This is the question I thought of right now.

[FLYBOYJ]

Originally Posted by syscom3

It influenced no one as the mossie was the last wooden plane to fly in a war.

Canvas and wood flight controls were being used since the beginning of flight.

One possible reason for the use of fabric control surface was the good strength to weight rations coupled with the need to reduce inertial forces under high deflections.

Canvas IS NOT a fabric material - grade A cotton or Irish linen....

Originally Posted by comiso90

Yes but the tremendous success of the mosquito may may have caused designers a give second look at canvas and wood on a high performance fighter. I'm sure using fabric and wood on a first rate "modern" fighter wasn't popular with some engineers.

Parts of the Vampire were made from wood! See Pb's comment!

Originally Posted by Snautzer

I can think of this

Ballooning of the fabric stuff occurs when the plane is in very high speed, so there was no direct reason (nothing to gain) to change.

Cost would also being a factor i guess as wood etc was the known

Ballooning will occur at high speed with deteriorating fabric although the faster the aircraft went, the more the fabric control surface was subject to ballooning.

Originally Posted by ppopsie

I asked the same question to multiple aviation people and got almost the same answer that to reduce the weight aft of hing lines was the primary reason. I understand this.

The situation changed when high speed planes with more than 400mph of top speed, like the Corsair, started to appear. The control force became increasingly heavier and heavier on these types. Most of the later WW2 American fighters suffered this problem.

.....So what were the airelons on the early prototype F4U(s)? Were these remain unchanged through its developing stage? This is the question I thought of right now.

I believe they started out as fabric control surfaces and were later changed to metal, but I believe the trim tabs remained wood.