ADS NOT DISPLAYED TO REGISTERED USERS.
+ Reply to Thread
Results 1 to 9 of 9

Radial engine cooling

Engines Discuss Radial engine cooling in the Technical forums; Hello, Folks I have a question- If a person was going to use a radial engine for non-aircraft use does ...

  1. #1
    Junior Member
    Join Date
    Jun 2008
    Posts
    3
    Country
    United States

    Radial engine cooling

    Hello, Folks I have a question- If a person was going to use a radial engine for non-aircraft use does anyone make a cooling fan to install in place of the propeller? Thanks, John


  2. #2
    Senior Member Thorlifter's Avatar
    Join Date
    Jun 2004
    Location
    Dallas, Tx
    Posts
    6,852
    Country
    United States
    That's going to be one hell of a lawn mower John!!!!!

  3. #3
    Senior Member wilbur1's Avatar
    Join Date
    Nov 2007
    Location
    Escondido,Ca
    Posts
    2,206
    Country
    United States
    I would think they have, the other thing is you can run it on methanol to help with the cooling

    Dont shoot him...... It will just make him angry.

  4. #4
    Senior Member <simon>'s Avatar
    Join Date
    Jan 2008
    Location
    Heyfield, Victoria
    Posts
    280
    Country
    Australia
    i'm dying to know what you are planning to do with this engine!

    I think if you simply had it running outside somewhere for the simple pleasure of hearing a radial at work, it shouldn't overheat.
    Really depends on what use you have in mind for this engine.

    A prop/fan always adds to the effect anyway!

  5. #5
    Junior Member
    Join Date
    Jul 2008
    Posts
    1
    Country
    United States
    Do not run any aircraft engine on methanol, will eat many internal seals, gaskets etc.......

    The engines on test stands were run with a dummy prop mostly to load the engine and prevent over revving. Many radials are tolerant of high MP but not over RPM.

    Good Luck!

  6. #6
    Junior Member
    Join Date
    Dec 2007
    Location
    UK
    Posts
    3
    Country
    United Kingdom
    You need a testbed prop, as advised above. Some form of ring cowls and cylinder baffles are vital to maintain proper cooling or you're going to have problems in the future. You'll also need the following minimum instrumentation as well as an oil cooler and exhaust collector ring:
    Tacho,
    Manifold Pressure,
    Oil Pressure,
    Oil Temperature,
    Cylinder Head Temperature.

    Note - overboosting (excessive manifold pressure) will ruin your engine if it's supercharged. You really need to understand the principles of blown aero-engine operation before you run at more than low power.

  7. #7
    Banned
    Join Date
    Jun 2007
    Location
    Pine Mountain Lake, California
    Posts
    981
    Country
    United States
    The only two applications I can think of that doesn't involve a propeller cooling the engine was as an engine for a tank (the M2/3/4 series of early-WWII American tanks), and the H-19 helicopter (see below). In both cases, I believe an auxiliary fan with ducting was used to blow air over the cylinders when the engine was operating.


  8. #8
    Senior Member
    Join Date
    May 2008
    Posts
    186
    Country
    United States
    There are many that run radial aircraft engines with cropped off propellers. Just keep an eye on cylinder head temperatures.

  9. #9
    Senior Member
    Join Date
    Jun 2005
    Posts
    101
    Sherman tanks, didnt they have aircooled radial engines.And some MTB??

+ Reply to Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86