Airbrushing

Negative Creep · 05-02-2007, 09:42 AM

JManaged to break part of my current airbrush (don't ask) and thought this time I'd by a compressor as well. I've seen this one on ebay, would this be ok for general modeling work? It does seem quite good for the price

eBay.co.uk: AIRBRUSH KIT + AIR BRUSH COMPRESSOR (item 130107512541 end time 04-May-07 15:46:29 BST)

Wurger · 05-03-2007, 09:22 AM

Hi mate !!!
I think this set can be good for general modeling work.However,the airbrush is also available with 2mm nozzle in diameter,but if the 3mm nozzle is enough for you this airbrush is acceptable.As far as the compressor is concerned,it looks like the one with a piston to make pressure but not with a membrane.A compressor with a piston is better that the one with a membrane for giving stable pressure and it can work longer.Of course it depends on a making quality of a compressor too.The technical datas of thie compressor seem to be O.K.Air pressure 30psi seems to be enough for the airbrush and all acrylic paints but for oil enamels I'm not sure.You can finally make that kind of enamels much more diluted.

The cost of this is in pounds so I cannot say anymore about it 'cos there are different prices in Poland.But the price seems to be high indeed.

Negative Creep · 05-03-2007, 10:55 AM

Thanks for the advice. I never use enamel paints anyway, as I'm allergic to the cleaning agents. All the compressors I've seen in the shops are £100+, so this is pretty cheap!

Wurger · 05-04-2007, 01:31 AM

Hi !!!
Ah,I've almost forgotten about your allergy.

So the compressor can be O.K.
But I forgot to draw your attention to its boosting - VOLTAGE 240 VOLTS (PLUG INCLUDED ).Won't you have any problems with this?

BTW. There is a similar compressor in my friend's shop.The difference is in the air pressure.It gives a bit smaller one.Its cost is about 64 GBP.

Negative Creep · 05-04-2007, 07:20 AM

All British electrics run at 240V

Wurger · 05-04-2007, 09:11 AM

In Poland 220-230V

Negative Creep · 05-04-2007, 10:39 AM

Yep, we English like to be different from the rest of Europe

Wurger · 05-04-2007, 10:51 AM

Not only you.In The USA is 110V isn't it?
In Russia, for instance, the railways have a different gauge.

Negative Creep · 05-04-2007, 03:03 PM

We have a great mix here; 3 pin plugs, 50mHZ TV's, metric weights and measures, imperial road signs, right hand drive cars. Plus when the railways first started out, we had both narrow and broad gauge rails for quite some time

All because we weren't invaded by Napoleon!

Wurger · 05-05-2007, 11:07 AM

Quote:

Originally Posted by Negative Creep

All because we weren't invaded by Napoleon!

We were, unfortunately.And then- some hundreds of years of a captivity.

tpikdave · 05-07-2007, 12:44 AM

Negative Creep

You can try a company called "Dick Blick" for airbrushes and compressors. 30 to 40lbs compression is fine for modeling or art work. I have a Badger compressor that I have used for over 10 years. It cost me $150. You can get the same compressor from Harbor Freight for $39.00

I don't even use it anymore. I have a couple contractor compressors, the small one is a Delta and puts out up to 90psi, but it will adjust down to 10 psi. It also has a 1.5 gallon tank so its not going on and off a lot.

DOUGRD · 05-07-2007, 10:30 PM

Hey N.C. How 're you doing? My modeling expertise is a little rusty but I've used both Badgers and a Paache (?) with my Badger compressor which when I bought it new was only $70.00 (USD). That dated it didn't it? Anyway I found that with an air tank and a moisture trap (I made my trap using a small glass jar, some brass tubing and a paper towel) and an air valve on top of the tank output line I got a nice steady, dry air flow that I could regulate down to a whisper. I did a Storch with wavy band camo and it turned out really nice. I hope that's some help?

Wurger · 05-08-2007, 02:28 PM

Hi Dougrd !!!
It a good idea to make a moisture trap with a small glass jar.

DOUGRD · 05-28-2007, 08:56 PM

Hey NC what's the latest? Did you buy that air compressor. What kind of airbrush did you get? Wurger: I'm glad you like the air trap idea. I can't take credit for the idea though, a friend of mine way back when told me about it and showed me how he did it.

Negative Creep · 05-29-2007, 09:30 PM

I forgot to mention that I brought it last payday; the results can be seen in the 'Post your Models' thread. It's actually a really good bit of kit, feels very strong and good value for money. I haven't managed to do fine lines as of yet as the pressure doesn't seem to be adjustable, always going to 60 psi. Haven't managed anything intricate yet, I'm not sure if this is due to the nature of the airbrush, or (more likely) my inexperience